Hyundai Santa Fe (DM): Instrument Cluster. Repair procedures - Indicators And Gauges - Body Electrical SystemHyundai Santa Fe (DM): Instrument Cluster. Repair procedures

Removal

1.
Disconnect the negative (-) battery terminal.
2.
Remove the cluster fascia panel (A).
3.
Remove the cluster (A) from the housing after removing 2 screws.
4.
Disconnect the cluster connecter (A) and then remove the cluster (B).

Installation

1.
Connect the cluster connector.
2.
Install the cluster assembly.
3.
Install the cluster facia panel.
4.
Connect the negative (-) battery terminal.

Inspection

1.
Check point (Warning indicator)
NO
 Ref
Symbol
 Color
 Name
 Signal Input
 Signal Control
(Unit / Sensor)
 Check Point
1

Green
 Turn Left
 C-CAN
 BCM
1.
CAN line failure
2

Green
 Turn Right
 C-CAN
3

Green
 Front Fog
 C-CAN
 BCM
1.
CAN line failure
4

Blue
 High Beam
 C-CAN
 BCM
1.
CAN line failure
5

Green
 Low Beam
 C-CAN
 BCM
1.
CAN Line failure
6

Green
 Tail Lamp
 C-CAN
 BCM
1.
CAN Line failure
7

Green
 Cruise
 C-CAN
 EMS
1.
CAN line failure
8

Green
 SET
 C-CAN
 EMS
1.
CAN line failure
9

Red
 Seat Belt
 C-CAN
 BCM
1.
CAN line failure
10

Red
 Air Bag
 C-CAN
 ACU
1.
CAN line failure
11

Yellow
 Trunk Open
 C-CAN
 BCM
1.
CAN line failure
12

Red
 Door Open
 C-CAN
 BCM
1.
CAN line failure
13

Red
 High Temperature
 C-CAN
 EMS
1.
CAN line failure
14

Yellow
 Immobilizer
 C-CAN
 SMK
1.
CAN line failure
15

Yellow
 ABS
 C-CAN
 ESC
1.
CAN line failure
16

Yellow
 EPB
 C-CAN
 EPB
1.
CAN line failure
17

Yellow
 ESC
 C-CAN
 ESC
1.
CAN line failure
18

Yellow
 ESC OFF
 C-CAN
 ESC
1.
CAN line failure
19

Yellow
 TPMS
(Tread & Fail)
 C-CAN
 TPMS
1.
CAN line failure
20

Yellow
 Fuel Low
 Hardwire
 Fuel Sender
1.
Fuel sender failure
2.
Wiring failure
21

Red
 Parking Brake
 C-CAN
 BCM
TCS
EPB
1.
CAN line failure
22

Yellow
 Oil Pressure
 Hardwire
 Oil Pressure Sensor
1.
Wiring failure
23

Red
 Battery Charge
 Hardwire
 Battery Sensor
1.
Wiring failure
24

Yellow
 Check Engine
 C-CAN
 EMS
1.
CAN line failure
25

Yellow
 Low Washer
 Hardwire
 Water Level Sensor
1.
Wiring failure
26

Green
 AUTOHOLD
(Green)
 C-CAN
 ESC
1.
CAN line failure

Yellow
 AUTOHOLD
(Yellow)
 C-CAN
 ESC
1.
CAN line failure

White
 AUTOHOLD
(White)
 C-CAN
 ESC
1.
CAN line failure
27

Green
White
Yellow
 LDWS
 C-CAN
 LDWS
1.
CAN line failure
28

Green
 Active ECO
 Hardwire
 ECO ON/OFF Switch
1.
Switch failure
2.
Wiring failure
29

Yellow
 4WD Diagnosis
 C-CAN
 4WD Unit
1.
4WD unit failure
2.
CAN line failure
30

Yellow
 4WD LOCK
 C-CAN
 4WD ECU
1.
4WD ECU failure
2.
CAN line failure
31

Yellow
 Glow
 C-CAN
 Glow Plug
1.
Glow plug failure
2.
CAN line failure
32

Red
 EPS
 C-CAN
 EPS Unit
1.
EPS unit failure
2.
CAN line failure
33

Red
 Water Seperator
 C-CAN
 Fuel filter water seperator sensor
1.
Water seperator sensor failure
2.
CAN line failure
34
Instrument Cluster. Description and Operation
Description Communication Network Diagram Abbreviation Explanation C_CAN Chassis Controller Area Network B_CAN Body Controller Area Network MM_CAN Multi media Controller Area Network SMK Smart Key ECU ...

Troubleshooting
Troubleshooting Symptom Possible cause Remedy Speedometer does not operate Cluster fuse (10A) blown Check for short and replace fuse Speedometer faulty Check speedometer CAN line faulty Check the EMS Wiring ...

See also:

Electronic Stability Control (ESC) Indicator Light
This indicator light illuminates: Once you set the ignition switch or Engine Start/Stop Button to the ON position. - It illuminates for approximately 3 seconds and then goes off. When there is a malfunction ...

Description and Operation
Description The 6-speed automatic transaxle consists of an overdrive clutch (OD/C), a one-way clutch (OWC), a lower and reverse brake (LR/B), an underdrive brake (UD/B), a 26 brake (26/B), and a 35R clutch ...

Side repeater lamp replacement
If the lamp bulb does not operate, have the vehicle checked by an authorized HYUNDAI dealer. ...