Hyundai Santa Fe (DM): Specifications
Specifications
Item |
Specification |
|
Type |
Motor Driven Power Steering |
|
Steering gear |
Type |
Rack & Pinion |
Rack stroke |
160mm |
|
Steering angle(Max.) |
Inner |
38.79°±1°30’ |
Outer |
31.92° |
Tightening Torques
Item |
Tightening torque (kgf.m) |
||
Nm |
kgf.m |
lb-ft |
|
Tire wheel lug nuts |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
Steering wheel lock nut |
44.1 ~ 49.0 |
4.5 ~ 5.0 |
32.5 ~ 36.2 |
Steering column assembly to Universal joint |
27.5 ~ 31.4 |
2.8 ~ 3.2 |
20.3 ~ 23.1 |
Steering column mounting bolts |
44.1 ~ 49.0 |
4.5 ~ 5.0 |
32.5 ~ 36.2 |
Steering column mounting nuts |
12.7 ~ 17.7 |
1.3 ~ 1.8 |
9.4 ~ 13.0 |
Universal joint to pinion of steering gear |
32.4 ~ 37.3 |
3.3 ~ 3.8 |
23.9 ~ 27.5 |
Tie rod end castle nut |
23.5 ~ 33.3 |
2.4 ~ 3.4 |
17.4 ~ 24.6 |
Steering gear box to sub freame |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
Stabilizer link nut |
98.1 ~ 117.7 |
10.0 ~ 12.0 |
72.3 ~ 86.8 |
Roll rod mounting bolt & nut |
107.9 ~ 127.5 |
11.0 ~13.0 |
79.6 ~ 94.0 |
Lower arm to knuckle |
98.1 ~ 117.7 |
10.0 ~12.0 |
72.3 ~ 86.8 |
Sub frame mounting bolts |
(A) 44.1 ~ 58.8 |
4.5 ~ 6.0 |
32.5 ~ 43.4 |
(B) 156.9 ~ 176.5 |
16.0 ~ 18.0 |
115.7 ~ 130.2 |
|
Upper roll rod bracket bolt |
(A) 107.9 ~ 127.5 |
11.0 ~ 13.0 |
79.6 ~ 94.0 |
(B) 49.0 ~ 63.7 |
5.0 ~ 6.5 |
36.2 ~ 47.0 |
Special Service Tools
Special Service Tools Tool (Number and Name) IIIustration Use 09561-11001 Steering wheel puller Remove the steering wheel ...
See also:
Emergency towing precautions
Turn the ignition switch to ACC so the steering wheel isn’t locked. Place the transaxle shift lever in N (Neutral). Release the parking bake. Press the brake pedal with more force than normal since ...
Tire sidewall labeling
This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify ...
Engine Control Module (ECM). Repair procedures
Removal When replacing the ECM, the vehicle equipped with the immobilizer must be performed procedure as below. [In the case of installing used ECM] 1) Perform "ECM Neutral mode" procedure with ...