Hyundai Santa Fe (TM): Power Windows
Description and operation
Function Of Safety Power Window |
When driver door power window auto-up switch is operated, safety function is
activated.
1. |
Safety function condition
When detect the force of 100N (using the 10N/mm spring) during the window
rising, window is reversed.
|
2. |
Length of window reversing (except holding the auto-up switch)
|
3. |
Length of window reversing (holding the auto-up switch)
|
4. |
Safety function is not available area
Safety function is not available during the 4mm from top of the door.
|
Initializing Method of the Safety Power Window
1. |
Initializing of Battery Connection
When the battery power is removed for over 5 minutes, safety power window
switch need the initializing.
|
2. |
Initializing of fail safe mode
|
Components and components location
Component Location |
1. DAU (Door
Area Unit) 2. Assist window switch 3. Front window motor |
4. Rear window
motor 5. Rear window switch |
Power Window Motor. Components and components location
Components |
Power Window Motor. Schematic diagrams
Circuit Diagram |
Power Window Motor. Repair procedures
Inspection |
Front Power Window Motor
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the front door trim.
(Refer to Body - "Front Door Trim")
|
3. |
Disconnect the connector (A) from the motor.
(A : Safety, B : Standard)
|
4. |
Connect the motor terminals directly to battery voltage (12V) and check
that the motor operates smoothly. Next, reverse the polarity and check
that the motor operates smoothly in the reverse direction. If the operation
is abnormal, replace the motor.
[Standard Window motor]
|
5. |
Connect the terminal No. 2 and No. 3 to battery voltage (12V) and check
that the motor operates smoothly when connecting the terminals below.
[Safety Window motor]
|
Rear Power Window Motor
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the rear door trim.
(Refer to Body - "Rear Door Trim")
|
3. |
Disconnect the connector (A) from the motor.
(A : Safety, B : Standard)
|
4. |
Connect the motor terminals directly to battery voltage (12V) and check
that the motor operates smoothly. Next, reverse the polarity and check
that the motor operates smoothly in the reverse direction. If the operation
is abnormal, replace the motor.
[Standard Window motor]
|
5. |
Connect the terminal No. 2 and No. 3 to battery voltage (12V) and check
that the motor operates smoothly when connecting the terminals below.
[Safety Window motor]
|
Power Window Switch. Components and components location
Components |
[Driver Power Window Switch] |
[Assist Power Window Switch] |
[Rear Power Window Switch] |
Power Window Switch. Schematic diagrams
Circuit Diagram |
[Driver Power Window Switch]
Driver safety switch
Front safety switch
ALL safety switch
[Assist Power Window Switch]
[Rear Power Window Switch]
Power Window Switch. Repair procedures
Diagnosis with diagnostic tool |
Diagnosis with diagnostic tool
1. |
In the body electrical system, failure can be quickly diagnosed by using
the vehicle diagnostic system (diagnostic tool).
The diagnostic system (diagnostic tool) provides the following information.
|
2. |
If diagnose the vehicle by diagnostic tool, select "DTC Analysis" and
"Vehicle".
|
3. |
Select the 'Data Analysis' and 'Car model'.
|
4. |
Select the 'DDM' to search the current state of the input/output data.
|
5. |
To forcibly actuate the input value of the module to be checked, select
option 'Actuation Test'.
|
Removal |
Driver Power Window Switch
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the front door trim.
(Refer to Body - "Front Door Trim")
|
3. |
Remove the power window bezzel assembl (A) after loosening the mounting
screws.
|
4. |
Remove the power window switch assembly (A) after loosening the mounting
screws.
|
Assist Power Window Switch
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the front door trim.
(Refer to Body - "Front Door Trim")
|
3. |
Remove the power window switch assembly (A) after loosening the mounting
screws.
|
Rear Power Window Swtich
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the rear door trim.
(Refer to Body - "Rear Door Trim")
|
3. |
Remove the power window switch assembly (A) after loosening the mounting
screws.
|
4. |
Check for continuity between the terminals in each switch position according
to the table. If the continuity condition is not normal, replace the
switch.
[Manual Window]
[Safety Window]
|
Installation |
Driver Power Window Switch
1. |
Install the power window switch assembly.
|
2. |
Install the front door trim after connecting the connector.
|
Assist Power Window Switch
1. |
Install the power window switch assembly.
|
2. |
Install the front door trim after connecting the connector.
|
Rear Power Window Swtich
1. |
Install the power window switch assembly.
|
2. |
Install the rear door trim after connecting the connector.
|
Power Door Mirrors
Components and components location Component Location 1. Power door mirror 2. Power door mirror switch 3. Power folding mirror switch Power Door Mirror Switch. Schematic diagrams Circuit Diagram Power ...Rear Glass Defogger
Components and components location Component Location 1. Rear glass defogger relay (Buil-in engine room relay box) 2. Rear glass defogger switch (Dual type) 3. Rear glass defogger switch (Manual type) ...See also:
Injured person
A seat belt should be used when an injured person is being transported. When this is necessary, you should consult a physician for recommendations. ...
Fuel Tank Pressure Sensor (FTPS). Repair procedures
Inspection 1. Connect the GDS on the Data Link Connector (DLC). 2. Measure the output voltage of the FTPS. Specification: Refer to "Specification" Removal 1. Turn the ignition switch OFF and ...
Specifications - Revised
Specifications Description Specifications Limit General Type In-line, DOHC Number of cylinders 4 Bore 88 mm (3.464 in) Stroke 97 mm (3.819 in) Total displacement 2359cc ...