Hyundai Santa Fe (TM): Special service tools
| Special Service Tools |
|
Tool(Number and Name) |
Illustration |
Use |
|
Ball joint puller 09568-2J100 |
|
Use for removal of ball joint |
|
Lower arm ball joint remover 09568-4R100 |
|
Removal of the lower arm ball joint. |
|
Band installer 0K495-C5000 |
|
Used for installing ear type boot band |
|
Band installer 09495-39100 |
|
Used for installing hook type boot band |
|
Differential bearing remover 09501-C9200 |
|
Used for removal of differential gear bearing |
|
Differential assembly working stand base 09501-C9231 |
|
Used for working on the differential carrier assembly (Use with 0K530-P2500, 0K501-P2232) |
|
Rear differential assembly working stand adapter 0K530-P2500 |
|
Used for working on the differential carrier assembly (Use with 09501-C9231, 0K501-P2232) |
|
Sub support 0K501-P2232 |
|
Used for working on the differential carrier assembly (Use with 09501-C9231, 0K530-P2500) |
|
Bearing remover 09501-C9310 |
|
Used for removal of the bearing (Use with 09452-2E000) |
|
Bearing remover 09452-2E000 |
|
Used as main body when removing the bearing (Use with 09501-C9310) |
|
Bearing race remover (Main body) 09501-C9140 |
|
Used for removal of the bearing race (Main body only) |
|
Bearing race remover 09501-C9320 |
|
Used for removal of the outside bearing race |
|
Bearing race remover 09501-C9330 |
|
Used for removal of the inside bearing race |
|
Rear differential bearing installer 0K530-P2300 |
|
Used for installing the differential gear bearing |
|
Rear differential bearing installer 0K530-P2200 |
|
Used for installing the pinion bearing race |
|
Pinion bearing race installer 09501-C9340 |
|
Removal & Installation of the differential assembly warking stand. |
|
Pinion oil seal installer 0K530-P2100 |
|
Used for installing the pinion oil seal (Use with 09231-H1100) |
|
Differential oil seal installer 09501-C9190 |
|
Used for installing differential case side oil seal L100:P147 (Use with 09231-H1100) |
|
Handle 09231-H1100 |
|
Using with 0K530-P2100, 09501-C9190 |
|
Backlash measurement supporter 0K530-P2400 |
|
Used to measure the backlash |
Specifications
Specification Items Inner side Outer side Front driveshaft Joint type HLSJ#104 BJ#104C Max. permissible angle 23° 45° Rear driveshaft Joint type CJ#79 Max. permissible angle 23° Rear differential Oil ...
Front Hub / Knuckle / Tone Wheel
Components and components location Components 1. Front knuckle 2. Dust cover 3. Front hub assembly 4. Front brake disc Repair procedures Removal • Be careful not to damage the parts located ...
See also:
Rear Center Seat Belt Retractor. Repair procedures
Replacement • When installing the belt, make sure not to damage the retractor. 1. Remove the second row seat back cover [LH]. 2. Loosen the rear center seat belt lower anchor mounting bolt (A). Tightening ...
Injector. Repair procedures
Inspection 1. Turn the ignition switch OFF. 2. Disconnect the injector connector. 3. Measure resistance between the injector terminals 1 and 2. 4. Check that the resistance is within the specification. ...
Roller Blind. Repair procedures
Replacement [Removal] 1. Open the roller blind using the panorama sunroof switch. • Leave 10 ~ 20cm (0.3937 ~ 0.7874 in) of the roller blind unopened. 2. Remove the roof trim. 3. Remove the roller blind ...
