Hyundai Santa Fe (DM): Specifications
Specifications
|
Item |
Specifications |
|
|
Transaxle type |
A6MF2 |
|
|
Engine model |
Gasoline 2.4GDI |
|
|
Torque converter type |
3-element, 1-stage, 2-phase type |
|
|
Torque converter size |
Ø236 mm (9.2913 in.) |
|
|
Oil pump system |
Parachoid |
|
|
Friction elements |
Clutch: 2EA |
|
|
Brake: 3EA |
||
|
OWC : 1EA |
||
|
Planetary gear |
3EA |
|
|
Gear ration |
1st |
4.639 |
|
2nd |
2.826 |
|
|
3rd |
1.841 |
|
|
4th |
1.386 |
|
|
5th |
1.000 |
|
|
6th |
0.772 |
|
|
Reverse |
3.385 |
|
|
Final gear ratio |
3.648 |
|
|
Fluid pressure balance piston |
2EA |
|
|
Accumulator |
4EA |
|
|
Solenoid valve |
8EA (VFS:6EA, ON/OFF:2EA) |
|
|
Shift lever position |
4 Range (P,R,N,D) |
|
|
Oil filter |
1EA |
|
VFS: Variable Force Solenoid
Sensors
Input Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
|
Operation condition (°C)°F |
((-)40 ~ 150)) -40 ~ 302 |
|
|
Air gap(mm)in. |
(0.95 ~ 1.65) 0.0374 ~ 0.0649 |
|
|
Output voltage(V) |
High |
1.18 ~ 1.68 |
|
Low |
0.59 ~ 0.84 |
|
Output Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
|
Operation condition (°C)°F |
((-)40 ~ 150)) -40 ~ 302 |
|
|
Air gap(mm)in. |
(0.25 ~ 0.70) 0.0098 ~ 0.0276 |
|
|
Output voltage (V) |
High |
1.18 ~ 1.68 |
|
Low |
0.59 ~ 0.84 |
|
Oil Temperature Sensor
▷ Type: Negative thermal coefficient type
▷ Specifications
|
Temp.(°C)°F |
Resistance (kΩ) |
|
(-40)-40 |
48.1 |
|
(-20)-4.0 |
15.6 |
|
(0)32.0 |
5.88 |
|
(20)68.0 |
2.51 |
|
(40)104.0 |
1.11 |
|
(60)140.0 |
0.61 |
|
(80)176.0 |
0.32 |
|
(100)212.0 |
0.18 |
|
(120)248.0 |
0.10 |
|
(140)284.0 |
0.06 |
|
(165)329.0 |
0.03 |
Inhibiter Switch
▷ Type: Combination of output signals from 4 terminals
▷ Specifications
|
Power supply (V) |
12 |
|
Output type |
Pin to Pin |
Solenoid Valves
Direct control VFS[26/B, T/CON]
▷ Control type : Normal low type
|
Control Pressure kpa (kgf/cm², psi) |
9.81 ~ 500.14 (0.1 ~ 5.1,1.42 ~ 72.54) |
|
Current value(mA) |
50 ~ 850 |
|
Internal resistance(Ω) |
5.1 |
Direct control VFS[UD/B, OD/C, 35R/C]
▷ Control Type : Normal high type
|
Control Pressure kpa (kgf/cm², psi) |
500.14 ~ 9.81 (5.1 ~ 0.1,72.54 ~ 1.42) |
|
Current value(mA) |
50 ~ 850 |
|
Internal resistance(Ω) |
5.1 |
Line Pressure Control VFS
▷ Control type : Normal high type
|
Control Pressure kpa (kgf/cm², psi) |
500.14 ~ 9.81 (5.1 ~ 0.1,72.54 ~ 1.42) |
|
Current value(mA) |
50 ~ 850 |
|
Internal resistance(Ω) |
5.1 |
ON/OFF Solenoid Valve(SS-A, SS-B)
▷ Control type : Normal low type
|
Control pressure kpa (kgf/cm², psi) |
490.33 (5.0, 71.12) |
|
Internal resistance(Ω) |
10 ~ 11 |
Solenoid Valve Operation Table
|
|
SS-A |
SS-B |
UD/B-VFS |
OD/C-VFS |
35R/C-VFS |
26/B-VFS |
|
N/H |
N/H |
N/H |
N/L |
|||
|
N, P |
● |
|
● |
|
● |
|
|
1 |
Δ |
|
|
Δ |
● |
|
|
2 |
|
|
|
● |
● |
● |
|
3 |
|
● |
|
● |
|
|
|
4 |
|
|
|
|
● |
|
|
5 |
|
● |
● |
|
|
|
|
6 |
|
|
● |
|
● |
● |
|
L |
● |
|
|
|
● |
|
|
R |
● |
● |
● |
|
|
|
● : Connected status
Δ : Connedted at vehicle speed above 8km/h
Tightening Torques
|
Item |
N.m |
Kgf.m |
lb-ft |
|
TCM installation mounting bolt/nut |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Shift cable bracket mounting bolt |
14.7 ~ 21.6 |
1.5 ~ 2.2 |
10.9 ~ 15.9 |
|
Input shaft speed sensor mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Output shaft speed sensor mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Shift lever assembly bolt |
8.8 ~ 13.7 |
0.9 ~ 1.4 |
9.4 ~ 10.8 |
|
Inhibitor switch mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Valve body cover mounting bolt |
13.7 ~ 15.7 |
1.4 ~ 1.6 |
10.1 ~ 11.6 |
|
ATF Warmer mounting bolt |
7.8 ~ 11.8 |
0.8 ~ 1.2 |
5.8 ~ 8.7 |
|
Injection hole (eyebolt) |
2.9 ~ 4.9 |
0.3 ~ 0.5 |
2.2 ~ 3.6 |
|
Oil drain plug |
38.2 ~ 48.1 |
3.9 ~ 4.9 |
28.2 ~ 35.4 |
|
Torque converter mounting bolt |
45.1 ~ 52.0 |
4.6 ~ 5.3 |
33.3 ~ 38.3 |
|
Starter motor mounting bolts |
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39.8 |
|
Automatic transaxle upper mounting bolt (TM=>Eng) |
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39.8 |
|
Automatic transaxle lower mounting bolt (Eng=>TM) |
42.2 ~ 48.1 |
4.3 ~ 4.9 |
31.1 ~ 35.4 |
|
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39..8 |
|
|
Automatic transaxle mounting support bracket bolt |
58.8 ~ 78.5 |
6.0 ~ 8.0 |
43.4 ~ 57.9 |
|
Automatic transaxle mounting bracket bolt |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
Lubricants
|
Item |
Specified lubricant |
Quantity |
|
Transaxle fluid |
SK ATF SP-Ⅳ, MICHANG ATF SP-Ⅳ,NOCA ATF SP-Ⅳ, Hyundai Genuine ATF SP-Ⅳ
or other brands meeting the above specification approved by Hyundai Motors
Corp. |
7.1L (1.88 U.S gal., 7.50 U.S.qt., 6.24 Imp.qt.) |
Sealant
|
Item |
Specified sealant |
|
Rear cover |
LOCTITE FMD-546 or THREE-BOND TB1281B |
|
Torque converter housing |
Special Service Tools
Special Service Tools Tools (Number and name) Illustration Use 09200-3N000 Engine support fixture(Beam) Removal and installation of the transaxle. Except lower supporter, use beam only with new engine ...
See also:
Repair procedures
Fuel Pressure Test 1. Release the residual pressure in fuel line. (Refer to Fuel Delivery System - “Release Residual Pressure in Fuel Line”) When removing the fuel pump relay, a Diagnostic Trouble ...
Special service tools
Special Service Tools Tool (Number and Name) IIIustration Use 09568-2J100 Ball joint remover Tie rod end ball joint removal 09568-4R100 Ball joint remover Lower arm ball joint removal ...
Components and Components Location
Component Location 1. Power outlet relay 2. Start relay 3. Front deicer relay 4. Blower relay 5. Wiper relay (Low) 6. ACC relay 7. IG1 relay 8. IG2 relay 9. Cooling fan relay 10. Wiper relay (High) 11. ...
