Hyundai Santa Fe (TM): Multifunction Switch
Components and components location
Component |
1. Steering column 2. Multifunction switch |
3. Screw 4. Clock spring |
Specifications
Specifications |
Items |
Specifications |
|
Rated voltage |
DC 12V |
|
Operating temperature range |
-22 to +176°F (-30°C to +80°C) |
|
Rated load |
Dimmer & passing switch |
High : 0.2A (Relay load) Low : 0.2A (Relay load) Passing : 0.2A (Relay load) |
Lighting switch |
Lighting : 0.2A (Relay load) (High, Low, Auto) |
|
Fog lamp switch |
0.2A (Relay load) |
|
Turn signal switch |
6.6A (Lamp load) |
|
Wiper & mist switch |
Low : 4.5A (Motor load) High : 4.5A (Motor load) Intermittent : 0.25 mA Lock : Max. 28A (Motor load) Washer : 4.0A (Motor load) |
|
Rear wiper & washer |
Wiper : 1.0A (Relay load) Washer : 4.0A (Motor load) |
Repair procedures
Removal |
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the steering wheel.
(Refer to Steering System - "Steering Wheel")
|
3. |
Remove the steering column upper and lower shrouds.
(Refer to Body - "Steering Column Shroud Panel")
|
4. |
Disconnect the multifunction switch connector (A).
|
5. |
Loosen the screws (2EA) and then remove the multifunction switch assembly
(A).
|
Installation |
1. |
Install the multifunction switch.
|
2. |
Install the clock spring and steering wheel.
|
3. |
Install the steering column upper and lower shrouds.
|
4. |
Install the steering wheel.
|
Inspection |
1. |
Check for continuity between the terminals in each switch position as
shown below.
|
1. |
In the body electrical system, failure can be quickly diagnosed by using
the vehicle diagnostic system (diagnostic tool).
The diagnostic system (diagnostic tool) provides the following information.
|
2. |
If diagnose the vehicle by diagnostic tool, select "DTC Analysis" and
"Vehicle".
|
3. |
If check current status, select the "Data Analysis" and "Car model".
|
4. |
Select the 'IBU_BCM' to search the current state of the input/output
data.
|
Audio
Components and components location Component Location 1. Audio unit 2. Tweeter speaker 3. Roof antenna (Radio) 4. Front door speaker 5. Rear door speaker 6. Antenna feeder cable 7. Antenna cable connector ...Horn
Components and components location Component Location 1. Horn switch 2. Horn relay (Engine room compartment) 3. Horn (Low pitch) 4. Horn (High pitch) 5. Clock spring Repair procedures Removal 1. Remove ...See also:
Automatic-dimming function
Your mirror will automatically dim upon detecting glare from the vehicles traveling behind you. The autodimming function can be controlled by the Dimming ON/OFF Button: 1. Pressing and hold the button ...
Thermostat. Repair procedures
Removal and Installation Removal of the thermostat would have an adverse effect, causing a lowering of cooling efficiency. Do not remove the thermostat, even if the engine tends to overheat. 1. Drain engine ...
Hood Latch. Repair procedures
Replacement [Hood upper latch assembly] 1. After loosening the mounting bolts, then remove the hood upper latch assembly (A). Tightening torque : 7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft) 2. Install ...