Hyundai Santa Fe (TM): Quarter Fixed Glass - Body (Interior and Exterior)Hyundai Santa Fe (TM): Quarter Fixed Glass

Components and components location

Components

1. Quarter Fixed Glass

Repair procedures

Replacement
[Removal]
  
•
Put on gloves to prevent hand injuries.
  
•
Use seat covers to avoid damaging any surfaces.
1.
Remove the rear pillar trim.
(Refer to Interior Trim - "Rear Pillar Trim")
2.
Loosen the quarter fixed glass mounting nuts.
Tightening torque :
3.9 - 4.4 N.m (0.4 - 0.5 kgf.m, 2.9 - 3.3 lb-ft)

3.
Cut out the quarter fixed glass sealant using the utility knife.
  
•
Do not scrape down to the painted surface of the body as bonding strength may get diminished on damaged paint.
  
•
Remove the rubber dam and fastereners from the body.
•
Mask off surrounding surfaces before painting.
4.
Remove the quarter fixed glass (A).
[Installtion]
1.
With a putt knife, scrape the old adhesive smooth to a thickness of about 2mm (0.08 in.) on the bonding surface around the entire quarter fixed glass flange.
  
•
Do not scrape down to the painted surface of the body as bonding strength may get diminished on damaged paint.
•
Mask off surrounding surfaces before painting.
•
Remove the fasteners from the body.
2.
Clean the body bonding surface with a sponge dampened in alcohol. After cleaning, keep the surface away from oil, grease and water.
3.
With a sponge, apply a light coat of glass primer along the edge of the quarter fixed glass, and then lightly wipe it off with a gauze or cheese cloth.
  
•
Do not apply body primer to the quarter fixed glass, and do not get body and glass primer sponges mixed up.
•
Never touch the primed surfaces with your hands. If you do, the adhesive may not bond to the quarter fixed glass properly, causing a leak after the quarter fixed glass in installed.
•
Keep water, dust, and abrasive materials away from the primed surface.
4.
With a sponge, apply a light coat of body primer to the original adhesive remaining around the flange. Let the body primer dry for at least 10 minutes.
  
•
Do not apply glass primer to the body, and be careful not to mix up glass and body primer sponges.
•
Never touch the primed surfaces with your hands.
5.
Install the quarter fixed glass and nuts.
Tightening torque :
3.9 - 4.4 N.m (0.4 - 0.5 kgf.m, 2.9 - 3.3 lb-ft)

  
•
Install the quater fixed glass by tightening the bolts, in the sequence as shown.

6.
Install the rear pillar trim.
(Refer to Interior Trim - "Rear Pillar Trim")
Tail Gate Window Glass
Components and components location Components 1. Tailgate window glass Repair procedures Removal    • Put on gloves to prevent hand injuries.    • Use seat covers to avoid damaging ...

Floor Carpet
Repair procedures Replacement    • Put on gloves to prevent hand injuries.    • When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent ...

See also:

Vehicle handling instructions
As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control, an accident or vehicle rollover. Specific design characteristics (higher ground clearance, ...

Timing System
Components and components location Components 1. Front oil seal 2. Timing chain cover 3. Timing chain 4. Cam to cam bracket 5. Timing chain guide 6. Timing chain tensioner arm 7. Timing chain tensioner ...

Components and Components Location
Component Location 1. Audio unit 2. Tweeter speaker 3. Roof antenna (Radio+SDARS) 4. Front door speaker 5. Rear door speaker 6. Antenna feeder cable 7. Antenna cable connector ※ SDARS : Satellite ...